( مشاهده پاسخ شماره 1 تا 2 / از مجموع 2 پاسخ )

موضوع: اجزاء یک بیو گاز فلر

  1. #1

    تاریخ عضویت
    Jul 2009
    رشته
    مهندسی شیمی
    نوشته ها
    514

    پیش فرض اجزاء یک بیو گاز فلر

    Inlet Flame Arrestor
    The John Zink® landfill/wastewater flare systems are designed to meet a high level of operational safety. Installed at the flare waste gas inlet, an in-line flame arrester stops flames from entering the gas piping system in the event of an operational malfunction. Our flame arrester features an aluminum housing, housing drain and removable aluminum internals. The internal elements can be easily removed and cleaned while leaving the flame arrestor body in place.
    Automatic Block Valve
    John Zink's automatic block valve assembly consists of a high performance butterfly valve and fail-closed pneumatic actuator. The pneumatic actuator includes a three-way solenoid valve, speed control valve, position indicator and auxiliary switches. The ANSI 150-lb high-performance butterfly valve has a carbon steel wafer body, 316 stainless steel disk, stainless steel shaft, and PTFE seal material.
    ZMS Moisture Separator
    Our ZMS moisture separator features HDPE (high density polyethylene) or internal coated carbon steel, flanged inlet and outlet, drain connection, level gauge, stainless steel demister element for moisture collection, differential pressure gauge around the demister element, and a flanged top for accessibility and maintenance.
    Flow Meter
    Insertion mass flow meter assembly with 316 stainless steel probe for 1-in. NPT mounting.
    Chart Recorder
    Install a panel-mounted Honeywell model DR4500T Digital Circular Chart Recorder on your system. The circular chart recorder is microprocessor based and draws the chart on paper as data is recorded. Users can design the chart to match specific applications. The recorder has flow totalization capabilities, an output display screen, and two inputs (four input options available) receiving 4 to 20 mA signals. With this option, the Honeywell controller includes an optional output signal allowing the recorder and controller to read the same temperature from the thermocouple.
    Automatic Telephone Dialer
    In the event of an alarm condition our panel-mounted, voice programmable automatic dialer with four digital inputs and a rechargeable battery reserve is able to dial multiple telephone numbers for instant notification of problems or operating conditions.
    Access Ladder
    The galvanized, safety ladder provides access to thermocouples. Equipment includes a ladder, safety rails, two safety belts and personnel protection screening behind the ladder and around the thermocouple ports. A lockable gate is also available.
    Service Platform
    Zink's 150° service platform, designed per OSHA requirements, provides access to stack sample ports. A continuous band of personnel protection screening around the sample ports is included with this option.
    Hinged Damper
    For easy access to the bottom of the flare stack for inspection and maintenance of the burners specify that one of the manual dampers be hinged.
    Control Panel Weather Hood
    The fabricated steel hood is designed to limit control panel exposure to the elements. The hood provides approximately 4 ft of overhang to the front and 2 ft to the rear. The hood comes with a fluorescent light assembly for enhanced visibility of the panel components at night.
    Industrial Surface Finish
    Apply a coat of Sherwin Williams Kem® High Temperature, aluminum top coat, coated 1 to 2 mils DFT over the standard Sherwin Williams Zinc Clad II primer to provide an enhanced finish with superior corrosion protection up to 750° F.
    Flare Foundation Template
    Zink's enclosed-flare base ring foundation template is constructed of 1/4-in. carbon steel plate to assist in setting and installing the anchor bolts in the field. The template is shipped prior to the flare, so that it can be used at the time the flare foundation is formed.
    Methane Analyzer
    The microprocessor based analyzer uses dual wavelength, non-dispersive infrared absorption to detect total percent volume methane. The unit is field configurable with a 4 to 20 mA output signal.
    Oxygen Analyzer
    The microprocessor based analyzer uses a micro fuel cell for percent oxygen detection. System shutdown occurs if high oxygen concentrations are detected in the waste gas stream. The unit is field configurable with a 4 to 20 mA output signal.
    Combination Methane and Oxygen Analyzer
    The combined package provides continuous measurement of percent oxygen and total volume percent methane. Methane detection occurs with a microprocessor based analyzer utilizing dual wavelength, non-dispersive infrared absorption. Oxygen detection occurs with a microprocessor based analyzer utilizing a micro fuel cell. The unit is field configurable and with 4 to 20 mA output signals.
    Underwriters Laboratories Classification
    John Zink Company is dedicated to ensuring the highest level of quality and safety standards in its products. This performance level is reflected in all products and provides the opportunity to apply the Underwriters Laboratories (UL) listing symbol for Industrial Control Panels on motor starters and a UL classification symbol on Flare Control Panels. This option is provided for applications requiring UL Certification.

    افراد موفق کارهای متفاوت انجام نمی دهند، بلکه کار را به صورتی متفاوت انجام می دهند.











  2. #2

    تاریخ عضویت
    Jul 2009
    رشته
    مهندسی شیمی
    نوشته ها
    514

    پیش فرض پاسخ : اجزاء یک بیو گاز فلر

    شرح فرآیند مشعل (Flare)
    دانلود در ضمیمه
    فايل هاي پيوست شده
    افراد موفق کارهای متفاوت انجام نمی دهند، بلکه کار را به صورتی متفاوت انجام می دهند.











اطلاعات موضوع

کاربرانی که در حال مشاهده این موضوع هستند

در حال حاضر 1 کاربر در حال مشاهده این موضوع است. (0 کاربران و 1 مهمان ها)

موضوعات مشابه

  1. کمپرسورهای تبرید ( Refrigeration Compressor )
    توسط محمد بهبهانی در انجمن مقالات مهندسی مکانیک
    پاسخ: 0
    آخرين نوشته: 09-28-2009, 12:34 AM
  2. تجزیه و تحلیل مسائل طراحی اجزاء
    توسط آرمان بنافی در انجمن کتاب های مهندسی شیمی
    پاسخ: 0
    آخرين نوشته: 08-29-2009, 02:46 AM

کلمات کلیدی این موضوع

مجوز های ارسال و ویرایش

  • شما نمیتوانید موضوع جدیدی ارسال کنید
  • شما امکان ارسال پاسخ را ندارید
  • شما نمیتوانید فایل پیوست کنید.
  • شما نمیتوانید پست های خود را ویرایش کنید
  •